Restoring An Extended Storage Engine
Use the following procedure to restore an engine that has been in extended storage.
- Remove the covers and tape from all of the openings of the engine, fuel tank and electrical equipment. Do not overlook the exhaust outlet.
- Remove the plugs from the inlet and outlet fuel lines and connect the lines to their proper position.
- Wash the exterior of the engine with fuel oil to remove the rust preventive. (Do NOT wash electrical components.)
- Remove the rust preventive from the flywheel.
- Remove the paper strips from between the pulleys and drive belts.
- Fill the crankcase to the proper level, with the recommended grade of lubricating oil listed in Table
"Recommended Engine Oil"
. Use a pressure lubricator to insure all bearings and rocker shafts are oiled.
SAE Viscosity Grade
3.7 cP (minimum)
- Fill the fuel tank with one of the fuels listed in Table
"Fuel Oil Selection Chart"
General Fuel Classification
No. 1 ASTM 1-D
No. 2 ASTM 2-D
Gravity, °API (Not Specified in ASTM D 975)
Flash Point, Minimum- °F (° C)
Viscosity, Kinematic-cSt @ 100 °F (40°C)
Cloud Point (Not Specified in ASTM D 975)
Sulfur Content, Maximum-wt%
0.05* (0.5 †)
0.05* (0.5 †)
Carbon Residue on 10%, Maximum-wt%,
Accelerated Stability, Total Insolubles, Maximum-mg/100 mL
Ash, Maximum-wt %
Cetane Number, Minimum (Differs from ASTM D 975)
Distillation Temperature, °F (° C)
No. 1 ASTM 1-D
No. 2 ASTM 2-D
IBP, Typical (Not Specified in ASTM D 975)
10% Typical (Not Specified in ASTM D 975)
50% Typical (Not Specified in ASTM D 975)
90% Maximum (Differs from ASTM D 975)
End Point, Maximum (Not Specified in ASTM D 975)
Water & Sediment, Maximum wt%
Note: * U.S. on-highway requirement
Note: † Nondramatic and off-highway applications only
Note: ‡ The cloud point should be 10°F (-12°C) below the lowest expected fuel temperature to prevent clogging of fuel filters by crystals.
- Close all of the drain cocks and fill the engine cooling system with clean soft water and proper inhibitors. Refer to "13.5.4 Cooling System" . If the engine is to be exposed to freezing temperatures, fill the cooling system with an ethylene glycol base antifreeze solution. Refer to "220.127.116.11 Antifreeze, Inhibited Ethylene Glycol" .
- Install and connect the battery. Ensure that the average specific gravity of the battery is 1.265 or higher. Refer to "11.1.8 Storage Battery" . Charge the battery if necessary.
- Perform the following:
- Keep the air cleaner housing tight on the air intake pipe.
- Ensure the correct filter replacement is used.
- Keep the air cleaner properly assembled so the joints are strictly air tight.
- Repair any damage to the air cleaner or related parts immediately.
- Inspect and clean or replace the air cleaner elements as operating conditions warrant.
- Carefully inspect the entire system periodically. Enough dust-laden air will pass through an almost invisible crack or opening to eventually cause damage to an engine.
- If a foam or fabric air cleaner element soaked with sticky dirt-holding substance was previously installed, check for the presence of coated engine components. Remove and clean them with a suitable solvent, as required, and blow dry with compressed air.
To avoid injury from flying debris when using compressed air, wear adequate eye protection (face shield or safety goggles) and do not exceed 276 kPa (40 psi) air pressure.
- Follow the manufacturer's recommendations covering the return of the transmission to service.
- Follow the manufacturer's recommendations covering the return of the power take-off to service.
- Remove the covers from the turbocharger air inlet and turbine outlet connections. Prelube the turbocharger. Refer to "6.5.7 Installation of Turbocharger"
Diesel engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects, and other reproductive harm.
- Always start and operate an engine in a well ventilated area.
- If operating an engine in an enclosed area, vent the exhaust to the outside.
- Do not modify or tamper with the exhaust system or emission control system.
- After all of the preparations have been completed, start the engine. The small amount of rust preventive compound which remains in the fuel system will cause smoky exhaust for a few minutes.
Note: Before subjecting the engine to a load or high speed, it is advisable to allow the engine to reach normal operating temperature. Then, monitor the DDEC Diagnostic Data Link for fault codes.
|Series 50 Service Manual - 6SE50|
|Generated on 10-13-2008|