Section 11.1 Preparation for a First Time Start

Section 11.1
Preparation for a First Time Start

Before starting an engine for the first time, carefully read and follow the instructions in this section. Also, refer to "13 Preventive Maintenance" .‪


Attempting to run the engine before studying these instructions may result in serious damage to the engine.‪


When preparing to start a new or overhauled engine or an engine that has been in storage, perform all of the operations listed below. Before a routine start (at each shift), see Daily Operations in the Preventive Maintenance Chart. Refer to "13.2 Daily Maintenance - All Applications" . Failure to perform required prestart operations may result in engine damage.‪

Section 11.1.1
Cooling System

Install all of the drain cocks and plugs in the cooling system as instructed below:‪

  1. Open the cooling system vents.
  2. Remove the filler cap and fill the cooling system with a coolant specified. Refer to "5.4 Coolant" . The coolant level should be within two inches (50 mm) of the filler neck to allow for fluid expansion.
  3. Close the vents, if used, after filling the cooling system.

Section 11.1.2
Lubrication System

The lubricating oil film on the rotating parts and bearings of a new or overhauled engine, or one which has been in storage, may be insufficient for proper lubrication when the engine is started for the first time.‪

It is recommended that the engine lubricating system be charged with a pressure prelubricator, set to supply a minimum of 172 kPa (25 lb/in.2 ) oil pressure, to ensure an immediate flow of oil to all bearings at the initial engine start-up. The oil supply line should be attached to the engine so that oil under pressure is supplied to the main oil gallery.‪

With the oil pan dry, use the prelubricator to prime the engine with sufficient oil to reach all bearing surfaces. Use lubricating oil as specified. Refer to "5.2 Lubricating Oil" . Then, remove the dipstick, wipe it with a clean cloth, insert and remove it again to check the oil level in the oil pan. Add sufficient oil, if necessary, to bring it to the full mark on the dipstick. Do not overfill.‪

If a pressure prelubricator is not available, fill the crankcase to the proper level with lubricating oil. Refer to "13.5.1 Lubricating Oil" . Then, prelubricate the upper engine parts by removing the valve rocker cover and pouring lubricating oil, of the same grade and viscosity as used in the crankcase, over the rocker arms, rocker arm shafts, camshaft lobes and camshaft follower rollers.‪

Section 11.1.3

When a turbocharger is replaced, or if the engine has been in storage, the turbocharger must be prelubricated by pouring oil into the oil supply inlet before the engine is started. Rotate the shaft to coat the bearings with oil.‪



Diesel engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects, and other reproductive harm.‪

  • Always start and operate an engine in a well ventilated area.
  • If operating an engine in an enclosed area, vent the exhaust to the outside.
  • Do not modify or tamper with the exhaust system or emission control system.


To avoid injury from contact with rotating parts when an engine is operating with the air inlet piping removed, install an air inlet screen shield over the turbocharger air inlet. The shield prevents contact with rotating parts.‪


The free floating bearings in the turbocharger center housing require positive lubrication. This is provided by the above procedure before the turbocharger reaches its maximum operating speed which is produced by high engine speeds. Starting any turbocharged engine and accelerating to any speed above idle before engine oil supply and pressure has reached the free floating bearings can cause severe damage to the shaft and bearings of the turbocharger.‪

Start and run the engine at idle until oil supply pressure has reached all of the turbocharger moving parts. A good indicator that all the moving parts are getting lubrication is when the oil pressure gage registers 138 kPa (20 lb/in.2 ) pressure at idle speed.‪

Section 11.1.4
Air Cleaner

Refer to OEM instructions for the air cleaner, and service accordingly.‪

Section 11.1.5

Check the oil level and, if necessary, fill the transmission case or torque converter to the proper level with the lubricant specified by the manufacturer.‪

Section 11.1.6
Fuel System

Fill the fuel tank with the fuel specified. Refer to "5.1 Fuel" . ‪

If the unit is equipped with a fuel valve, it must be opened. To ensure prompt starting, the fuel system between the pump and fuel return line must be full of fuel.‪

If the engine has been out of service for a considerable length of time, prime the fuel system between the fuel pump and the fuel return manifold. Before priming the fuel system, remove and fill both fuel filters with clean fuel oil and reinstall them.‪

Note: The engine fuel system is filled with fuel before leaving the factory. If the fuel is still in the system when preparing to start the engine, priming should be unnecessary.

Section 11.1.7
Drive Belts

Adjust all drive belts as recommended. Refer to "13.5.7 Drive Belts" .‪

Section 11.1.8
Storage Battery

Check the battery. The top should be clean and dry, the terminals tight and protected with a coat of silicone spray or petroleum jelly and the electrolyte must be at the proper level.‪

A hydrometer reading (corrected for the temperature of the electrolyte) should be 1.265 or higher. If necessary, charge the battery.‪

Section 11.1.9

Disengage the clutch, if the unit is so equipped.‪

Series 50 Service Manual - 6SE50
Generated on 10-13-2008

Leave a Reply

Your email address will not be published. Required fields are marked *