Series 50G/60G Troubleshooting – Section 2.3 Active DDEC Diagnostic Codes

Section 2.3
Active DDEC Diagnostic Codes

To determine if any active DDEC diagnostic codes apply to the Stall condition, perform the following:‪

1. Turn on the ignition. Plug the Diagnostic Data Reader (DDR) or the Detroit Diesel Diagnostic Link (DDDL) into the Diagnostic Connector.

   Note: Use the Pro-Link kit to connect the DDR. Use the PC card installed in the computer to connect the DDDL.

2. Read active codes by selecting the DIAGNOSTIC CODE MENU (ACTIVE CODES) on the DDR or DDDL.
3. If the active code is not in the Gas Specific DDEC diagnostic codes listed in Table "Gas Engine Specific DDEC Diagnostic Codes" or there are no active codes, then go to Active Non-Gas Specific DDEC Diagnostic Codes. Refer to "2.3.1 Active Non-Gas Specific DDEC Diagnostic Codes" .

   SAE Fault‪	Fault Type‪	DDEC Description‪	Flash Code‪	Action‪
   PID 51‪	FMI 0‪	Throttle plate position above normal range‪	65‪	Refer to "5.2 PID 51, FMI 0, Flash Code 65, Throttle Plate Position Above Normal Range" .‪
   PID 51‪	FMI 1‪	Throttle plate position below normal range‪	65‪	Refer to "5.3 PID 51, FMI 1, Flash Code 65, Throttle Plate Position Below Normal Range" .‪
   PID 51‪	FMI 2‪	Throttle plate position erratic‪	65‪	Refer to "5.4 PID 51, FMI 2, Flash Code 65, Throttle Plate Position Erratic" .‪
   PID 51‪	FMI 3‪	Throttle plate position sensor input voltage high‪	17‪	Refer to "5.5 PID 51, FMI 3, Flash Code 17, Throttle Plate Position Sensor Input Voltage High" .‪
   PID 51‪	FMI 4‪	Throttle plate position sensor input voltage low‪	18‪	Refer to "5.6 PID 51, FMI 4, Flash Code 18, Throttle Plate Position Sensor Input Voltage Low" .‪
   PID 51‪	FMI 7‪	Throttle plate position input fault‪	65‪	Refer to "5.7 PID 51, FMI 7, Flash Code 65, Throttle Plate Not Responding" .‪
   PID 91‪	FMI 3‪	TPS (foot pedal) input voltage high‪	21‪	Refer to "5.8 PID 91, FMI 3, Flash Code 21, Throttle Position Sensor Input Voltage High" .‪
   PID 91‪	FMI 4‪	TPS (foot pedal) input voltage low‪	22‪	Refer to "5.9 PID 91, FMI 4, Flash Code 22, Throttle Position Sensor Input Voltage Low" .‪
   PID 94‪	FMI 0‪	Fuel pressure high‪	47‪	Refer to "5.10 PID 94, FMI 0, Flash Code 47, Fuel Pressure High" .‪
   PID 94‪	FMI 1‪	Fuel pressure low‪	48‪	Refer to "5.11 PID 94, FMI 1, Flash Code 48, Fuel Pressure Low" .‪
   PID 94‪	FMI 3‪	Fuel pressure sensor input voltage high‪	37‪	Refer to "5.12 PID 94, FMI 3, Flash Code 37, Fuel Pressure Sensor Input Voltage High" .‪
   PID 94‪	FMI 4‪	Fuel pressure sensor input voltage low‪	38‪	Refer to "5.13 PID 94, FMI 4, Flash Code 38, Fuel Pressure Sensor Input Voltage Low" .‪
   PID 100‪	FMI 1‪	Oil pressure low‪	45‪	Refer to "5.14 PID 100, FMI 1, Flash Code 45, Oil Pressure Low" .‪
   PID 100‪	FMI 3‪	Oil pressure sensor input voltage high‪	35‪	Refer to "5.15 PID 100, FMI 3, Flash Code 35, Oil Pressure Sensor Input Voltage High" .‪
   PID 100‪	FMI 4‪	Oil pressure sensor input voltage low‪	36‪	Refer to "5.16 PID 100, FMI 4, Flash Code 36, Oil Pressure Sensor Input Voltage Low" .‪
   PID 105‪	FMI 0‪	Intake manifold air temperature high‪	44‪	Refer to "5.17 PID 105, FMI 0, Flash Code 44, Intake Manifold Temperature High" .‪
   PID 105‪	FMI 3‪	Intake manifold air temperature sensor input voltage high‪	27‪	Refer to "5.18 PID 105, FMI 3, Flash Code 27, Air Temperature Sensor Input Voltage High" .‪
   PID 105‪	FMI 4‪	Intake manifold air temperature sensor input voltage low‪	28‪	Refer to "5.19 PID 105, FMI 4, Flash Code 28, Air Temperature Sensor Input Voltage Low" .‪
   PID 106‪	FMI 0‪	Intake manifold pressure high‪	47‪	Refer to "5.20 PID 106, FMI 0, Flash Code 47, Intake Manifold Pressure High" .‪
   PID 106‪	FMI 1‪	Intake manifold pressure low‪	48‪	Refer to "5.21 PID 106, FMI 1, Flash Code 48, Intake Manifold Pressure Low" .‪
   PID 106‪	FMI 3‪	Manifold absolute pressure input voltage high‪	67‪	Refer to "5.22 PID 106, FMI 3, Flash Code 67, Manifold Absolute Pressure Sensor Input Voltage High" .‪
   PID 106‪	FMI 4‪	Manifold absolute pressure input voltage low‪	67‪	Refer to "5.23 PID 106, FMI 4, Flash Code 67, Manifold Absolute Pressure Sensor Input Voltage Low" .‪
   PID 108‪	FMI 3‪	Barometric pressure sensor input voltage high‪	86‪	Refer to "5.24 PID 108, FMI 3, Flash Code 86, Barometric Pressure Sensor Input Voltage High" .‪
   PID 108‪	FMI 4‪	Barometric pressure sensor input voltage low‪	87‪	Refer to "5.25 PID 108, FMI 4, Flash Code 87, Barometric Pressure Sensor Input Voltage Low" .‪
   PID 110‪	FMI 0‪	Coolant temperature high‪	44‪	Refer to "5.26 PID 110, FMI 0, Flash Code 44, Coolant Temperature High" .‪
   PID 110‪	FMI 3‪	The coolant temperature sensor input voltage is high‪	14‪	Refer to "5.27 PID 110, FMI 3, Flash Code 14, Coolant Temperature Sensor Input Voltage Low" .‪
   PID 110‪	FMI 4‪	Coolant temperature sensor input voltage low‪	15‪	Refer to "5.28 PID 110, FMI 4, Flash Code 15, the Coolant Temperature Sensor Input Voltage Low" .‪
   PID 111‪	FMI 1‪	Coolant level low‪	43‪	Refer to "5.29 PID 111, FMI 1, Flash Code 43, Coolant Level Low" .‪
   PID 111‪	FMI 3‪	Coolant level sensor input voltage high‪	16‪	Refer to "5.30 PID 111, FMI 3, Flash Code 16, Coolant Level Sensor Input Voltage High" .‪
   PID 111‪	FMI 4‪	Coolant level sensor input voltage low‪	13‪	Refer to "5.31 PID 111, FMI 4, Flash Code 13, Coolant Level Sensor Input Voltage Low" .‪
   PID 173‪	FMI 3‪	Exhaust temperature sensor input voltage high‪	81‪	Refer to "5.32 PID 173, FMI 3, Flash Code 81, Exhaust Temperature Sensor Input Voltage High" .‪
   PID 173‪	FMI 4‪	Exhaust temperature sensor input voltage low‪	82‪	Refer to "5.33 PID 173, FMI 4, Flash Code 82, Exhaust Temperature Sensor Input Voltage Low" .‪
   PID 174‪	FMI 3‪	Fuel temperature sensor input voltage high‪	23‪	Refer to "5.34 PID 174, FMI 3, Flash Code 23, Fuel Temperature Sensor Input Voltage High" .‪
   PID 174‪	FMI 4‪	Fuel temperature sensor input voltage low‪	24‪	Refer to "5.35 PID 174, FMI 4, Flash Code 24, Fuel Temperature Sensor Input Voltage Low" .‪
   SID 21‪	FMI 0‪	Too many SRS (missing TRS)‪	41‪	Refer to "6.2 SID 21, FMI 0, Flash Code 41, Too Many SRS (Missing TRS)" .‪
   SID 21‪	FMI 1‪	Too few SRS (missing TRS)‪	42‪	Refer to "6.3 SID 21, FMI 1, Flash Code 42, Too Few SRS (Missing SRS)" .‪
   SID 51‪	FMI 3‪	Aux. output No. 3, short to ground (high side)‪	31‪	Refer to "6.4 SID 51, FMI 4, Flash Code 31, Auxiliary Output No. 3, Short to Ground (High Side)" .‪
   SID 58‪	FMI 4‪	PWM driver No. 2 open circuit‪	63‪	Refer to "6.5 SID 58, FMI 4, Flash Code 63, PWM No. 2 Open Circuit" .‪
   SID 59‪	FMI 3‪	PWM driver No. 3 short to battery (+)‪	63‪	Refer to "6.6 SID 59, FMI 3, Flash Code 63, PWM No. 3 Short to Battery" .‪
   SID 59‪	FMI 4‪	PWM driver No. 3 open circuit‪	63‪	Refer to "6.7 SID 59, FMI 4, Flash Code 63, PWM No. 3 Open Circuit" .‪
   SID 65‪	FMI 3‪	Oxygen content circuit voltage high‪	23‪	Call Detroit Diesel Technical Service.‪
   SID 65‪	FMI 4‪	Oxygen content circuit voltage low‪	24‪	Call Detroit Diesel Technical Service.‪
   SID 76‪	FMI 0‪	Engine knock level above normal range‪	66‪	Refer to "6.8 SID 76, FMI 0, Flash Code 66, Engine Knock Level Above Normal Range" .‪
   SID 76‪	FMI 3‪	Engine knock level sensor input voltage high‪	66‪	Refer to "6.9 SID 76, FMI 3, Flash Code 66, Engine Knock Level Sensor Input Voltage High" .‪
   SID 76‪	FMI 4‪	Engine knock level sensor input low‪	66‪	Refer to "6.10 SID 76, FMI 4, Flash Code 66, Engine Knock Level Sensor Input Voltage Low" .‪
   SID 76‪	FMI 7‪	Engine knock level torque reduction‪	66‪	Refer to "6.11 SID 76, FMI 7, Flash Code 66, Engine Knock Level Torque Reduction" .‪
   SID 77‪	FMI 3‪	Gas Valve Position input voltage high‪	73‪	Refer to "6.12 SID 77, FMI 3, Flash Code 73, Gas Valve Position Input Voltage High" .‪
   SID 77‪	FMI 4‪	Gas Valve Position input voltage low‪	73‪	Refer to "6.13 SID 77, FMI 4, Flash Code 73, Gas Valve Position Input Voltage Low" .‪
   SID 232‪	FMI 0‪	Sensor supply voltage high‪	75‪	Refer to "6.14 SID 232, FMI 0, Flash Code 75, Sensor Supply Voltage High" .‪
   SID 232‪	FMI 1‪	Sensor supply voltage low‪	46‪	Refer to "6.15 SID 232, FMI 1, Flash Code 46, Sensor Supply Voltage Low" .‪

   Table 1. Gas Engine Specific DDEC Diagnostic Codes
4. If the active code is in the Gas Specific DDEC diagnostic codes listed in Table "Gas Engine Specific DDEC Diagnostic Codes" , then go to Active Gas Specific DDEC Diagnostic Codes. Refer to "2.3.2 Active Gas Specific DDEC Diagnostic Codes" .

Section 2.3.1
Active Non-Gas Specific DDEC Diagnostic Codes

Using the active Non-Gas Specific DDEC diagnostic code, troubleshoot as follows:‪

1. If there are no active codes, then troubleshoot the PSV operation. Refer to "2.6.1 PSV Operation Check" .
2. If there is an active code, then troubleshoot the Non-Gas Specific DDEC diagnostic codes. Refer to the DDEC III/IV Single ECM Troubleshooting Guide 6SE497.
3. If the engine still stalls, check for Low Fuel Pressure. Refer to "2.4 Low Fuel Pressure"
4. If the engine no longer stalls, troubleshooting is done.

Section 2.3.2
Active Gas Specific DDEC Diagnostic Codes

Using the active Gas Specific DDEC diagnostic code, troubleshoot as follows:‪

1. If there is a Low Fuel Pressure code (PID 94 FMI 1), then check for low fuel pressure. Refer to "2.4 Low Fuel Pressure" .
2. If there is a Gas Valve Position code (SID 77 FMI 0, SID 77 FMI 1, SID 77 FMI 3, SID 77 FMI 4, SID 77 FMI 7), then troubleshoot the PSV operation. Refer to "2.6.1 PSV Operation Check" .
3. If there are any other active Gas Engine Specific DDEC diagnostic codes listed in Table "Gas Engine Specific DDEC Diagnostic Codes" , then troubleshoot the code referenced in the table.
4. If the engine still stalls, check for Low Fuel Pressure. Refer to "2.4 Low Fuel Pressure" .
5. If the engine no longer stalls, troubleshooting is done.